2-Wire vs 3-Wire vs 4-Wire Transmitters: What Is the Difference?

The Short Answer

All three transmit the same 4-20 mA signal. The difference is how they get power. A 2-wire transmitter draws its power from the signal loop itself. A 3-wire transmitter has a separate supply wire and shares a common return with the signal. A 4-wire transmitter has completely separate power and signal pairs, so it can use much more power, including AC mains.

2-Wire (Loop-Powered) Transmitters

A 2-wire transmitter connects to the rest of the loop with just two wires. The DC supply, the transmitter and the receiver are all in series, and the transmitter regulates the current flowing through them between 4 and 20 mA. The transmitter runs on the small amount of power available at the bottom of the range, which is one reason the range starts at 4 mA and not 0 mA.

This is the most common design for pressure, level and temperature transmitters because it needs the least cable and the simplest installation.

3-Wire Transmitters

A 3-wire transmitter has a positive supply wire, a signal output wire and a shared 0 V common. The supply current and the signal current both return on the common wire. Because the transmitter is not starved for power, it can drive displays, heaters or more complex sensing electronics.

3-wire wiring is common for voltage-output sensors (0-10 V), many proximity sensors and some flow and analytical instruments. The trade-off is that the receiver and transmitter share a ground, which makes 3-wire devices more prone to ground loop problems on long runs.

4-Wire Transmitters

A 4-wire transmitter has one pair for power and a separate pair for the output signal. Power can be 24 VDC or AC mains, so the device can consume as much power as it needs. The output is often actively sourced and frequently isolated from the supply.

Magnetic flowmeters, analyzers and instruments with large displays or heaters are typically 4-wire.

How to Tell Them Apart

Wiring and power

Typical uses

The datasheet always says which type a transmitter is. Look for the terms loop-powered (2-wire), three-wire, or four-wire or separately powered (4-wire), and check the wiring diagram.

Connecting to a PLC Analog Input

PLC analog input cards are usually either sourcing, meaning they supply the loop power themselves, or sinking, meaning they expect the field device or an external supply to provide it. A 2-wire transmitter can work with either, provided only one power source is in the loop. A 4-wire transmitter with an active output must connect to a passive (sinking) input, or the two power sources will fight each other.

Where the card type and the transmitter type do not match, or where several devices share grounds, a signal isolator solves the problem.

Related Products

Our transmitters cover 2-wire, 3-wire and 4-wire designs. If you are unsure which suits your control system, our engineers can help.

Loop-powered and voltage-output pressure transmitters. View range

2-wire 4-20 mA submersible and hydrostatic level transmitters. View range

Isolate and convert signals between incompatible devices. View range

Frequently Asked Questions

Yes. Both terms describe a transmitter that takes its operating power from the 4-20 mA loop, using one pair of wires for power and signal.

No. The internal electronics decide the wiring type. To use a 3-wire or 4-wire device on a 2-wire input, use a signal isolator between them.

The most common cause is two power sources in one loop: an active 4-wire output connected to a sourcing PLC input. Use a passive input or an isolator.

More in This Category

What Is a 4-20 mA Signal?

A 4-20 mA signal is an analog DC current that represents a measured value, with 4 mA at the bottom of the range and 20 mA at the top. Because it is a current rather than a voltage, it travels long distances without losing accuracy, and the same two wires can power the sensor.

4-20 mA vs 0-10 V: Which Analog Output Should You Choose?

Choose 4-20 mA for long cable runs, electrically noisy plants and anywhere you need to detect a broken wire. Choose 0-10 V for short runs inside a panel or machine, where its simpler wiring and direct compatibility with many controllers and drives are an advantage.

What Is HART, and How Does It Work Over a 4-20 mA Loop?

HART (Highway Addressable Remote Transducer) is a digital protocol that rides on top of a standard 4-20 mA signal. It superimposes a small, high-frequency signal on the loop current, so the analog value keeps working while a HART device can also exchange configuration settings, diagnostics and extra measurements over the same two wires.

Need help choosing the right product?

Our engineers can help you select, configure and integrate the right sensor, instrument or industrial computer for your application.